PELATIHAN INTRODUCTION ADVANCED RIGGING

PENGANTAR TRAINING ADVANCED RIGGING TECHNIQUES

Lifting Supervisor is in charge of the initial work of erecting the load and to ensure that all rigging work is carried out in a safe and efficient manner, adhering to the regulation and to sound established customs and practices.
The first consideration must at all times, be directed toward the safeguarding life and limb. This consideration must extend to all persons in vicinity or likely to enter the vicinity.

TUJUAN TRAINING RIGGING PRINCIPLES AND PRACTICES

At the end of course, the participant should be able to:
* Observe general safety first rules and carry out his duties in a safe and responsible manner.
* Have knowledge of safe working load of the crane he is working with.
* Have a full knowledge of hand signal (Australian/New Zealand Standard)
* Understand the correct type of sling, hook shackle etc. for load.
* Have knowledge of the use of lifting beams, slings and chains.
* Understand the effect of doubling crane hoist rope on safe working.
* Understand use of rope, chain and shackle.
* Understand not to use damaged wire rope or fiber rope, slings or chain where the links are not free or kinked wire rope.
* Understand when slinging a load, pack between sling and load at all point where load has sharp corners, so as to prevent damage to sling.
* Design and apply the knowledge of lifting and lifting plan in their daily work

MATERI TRAINING ADVANCED LIFTING AND RIGGING METHODS

1. Introduction:
2. Definition of Dogger, Slinging & Crane Operator
3. Roles & Responsibilities of Rigger:
4. Rigger Certification System
5. Roles & responsibility of Crane Operator
6. Roles & Responsibility of Dogger
7. Roles & Responsibility of Slinger
8. Roles & Responsibility of Traffic Controller / Flagman
9. Roles & Responsibility of Lifting Supervisor
10. Accident & Prevention
11. Legislative Requirement:
12. International Standard: AS/NZS
13. Roles and Responsibilities :Crane operator, Crane Owner/End User, Facility/Site Owner, Lift Coordination, Lift Engineer/ Rigging Specialist, Workers and Crane Mechanic
14. Hazard And General Safety:
15. Outriggers and Crane Stability
16. Comparative Soil Bearing Capacities
17. Crane Selection Guide
18. Electrical Hazard
19. Public Road / Pedestrian Hazards
20. Utilities Overhead and underground
21. Accidents and Lesson learn
22. Signalling And Communication:
23. Two way Radios
24. Conventional Radio
25. Trunked Radio
26. Radio Direction for Crane Driver
27. Bell or Whistle Code
28. Hand Signal

1. Rigging Engineering Calculation
1. Determination on Centre of Gravity

* Rectangular Object
* Round or Oval Shape
* Multiple Load / Object

2. Rigging Engineering Calculation
3. Volume Calculation

* Rectangular Object
* Round or Oval Shape
* Triangle Object
* Cone Object
* Multiple Load / Object

Ropes & Knots for Rigger (Synthetic & Natural)
* Figure of Eight
* Reef knot
* Single Bowline
* End Splice
* Eye Splice
* Sheet Bend
* Timber Hitch
* Rolling Hitch
* 2 and Half Hitch
* Tagline Hitch
* Clove Hitch
* Etc

3. Rigging Engineering Calculation
4. Calculation of Mass

Basic Mass Calculation for Various Shapes of Loads Normally Engaged During Crane Operation versus volume
* Concrete / Cement
* Steel (Mild / Hard
* Liquid (Water)
* Wood
* Sand, etc

1. Lifting Appliances

* Selection on Sling material
+ Sling wire FSWR 1570
+ Sling wire FSWR 1770
+ Chain Sling GT80 / G100
+ Synthetic Webbing (Flat/Round Slings)
* Stacking and Clearances
* Clearance
* Stacking Steel Plate
* Stacking Rolled Steel Coils And Other Round Loads
* Stacking Timber
* Care, Maintenance, and Inspection on Sling Material
* Spreader Bar vs Stabilizer Bar
* Use of Slings / Hoists And Tag line
* Determination of W.L (SWL versus WLL)
* Minimum Breaking Force (MBF) and its usages

1. Rigging Engineering Calculation

* Safety Factor requirements
* Lifting Material & Human
1. Sling wire FSWR 1570
2. Sling wire FSWR 1770
3. Chain Sling GT80 / G100
4. Synthetic Webbing (Flat/Round Slings)
* ‘choke’ / Hitch Factor

1. Rectangular Load
2. Round Load

* Sling Angles Factor

1. Sudut 30o
2. Sudut 45o
3. Sudut 60o
4. Sudut 90o
5. Sudut 120o

* Determination of sling Strength based on diameter & Safety Factor

1. Sling Wire
2. Synthetic Sling
3. Chain Sling

* Determination of Sling length and lifting angle

1. Rigging Engineering Calculation

* Inspection of Slings & shackles and attachments

1. Sling Wire (5%)
2. Chain Sling (5%)
3. Synthetic Sling

Note: Determination of acceptance condition of slings and attachments. (Category 1 and Category 2)
2. Rigging Engineering Calculation

* Calculation of Multiple Sling

1. SWL Sling 1
2. SWL Sling 2

* Multiple Crane Lifting / Multiple @ Large Loads

1. Tendem Lifting
2. Crane Selection and Ordering crane
3. Crane type vs Load Chart & Working Radius

* Mobile Crane
* Crawler Crane
* Role & Responsibility of Lifting Supervisor
* Designing Lifting Plan
* Special Lifting (Professional Engineer Interferences): Lifting Specialist in General

1. Practical session on:
2. Determination of COG
3. Determination of Volume & Mass
4. Selection of slings
5. Lifting Techniques
6. Hand Signaling & Radio Communication
7. Inspection of Crane & Lifting Hoist appliances
8. Manual Lifting & Mechanical Lifting
9. Gin Wheel Application & Limitations

1. ASSESSMENT PAPER :
2. General Knowledge
3. Assessment Legislation
4. Assessment Calculation (Lifting Plan)

PESERTA TRAINING ADVANCED LIFTING AND RIGGING METHODS OFFLINE JOGJA

Training ini diperuntukkan bagi:

Staff, Supervisor, Manager hingga level diatasnya dari Divisi SDM atau divisi lainnya yang membutuhkan training ini.
Praktisi, Profesional atau siapapun yang ingin menambah pengetahuan mengenai bidang ini

METODE PELATIHAN ADVANCED LIFTING AND RIGGING METHODS KUALA LUMPUR

Pelatihan yang diberikan dalam pelatihan berupa Teori, Diskusi, Praktek dan Studi Kasus. Kami juga terbuka untuk selalu menyesuaikan kebutuhan dan pelatihan yang dilaksanakan.

INSTRUKTUR PELATIHAN RIGGING PRINCIPLES AND PRACTICES BANDUNG

Instruktur yang mengajar pelatihan ini adalah instruktur yang berkompeten di bidangnya dengan baik, datang dari kalangan akademisi maupun praktisi. Kami sangat terbuka jika Anda ingin berkomunikasi terlebih dahulu tim trainer sehingga outline materi dapat disesuaikan dengan outcome kompetensi yang diharapkan.

Jadwal Diorama Training Tahun 2025

Januari : 16-17 Januari 2025
Februari : 13-14 Februari 2025
Maret : 5-6 Maret 2025
April : 24-25 April 2025
Mei : 21-22 Mei 2025
Juni : 11-12 Juni 2025
Juli : 16-17 Juli 2025
Agustus : 20-21 Agustus 2025
September : 17-18 September 2025
Oktober : 8-9 Oktober 2025
November : 12-13 November 2025
Desember : 17-18 Desember 2025

Catatan: Jadwal tersebut dapat disesuaikan dengan kebutuhan calon peserta. Peserta dapat mengajukan tanggal pelaksanaan pelatihan. Sebelum melakukan booking tiket perjalanan maupun hotel mohon untuk menghubungi marketing kami terlebih dahulu. Kesalahan pemesanan tiket terkait jadwal tanpa surat konfirmasi (Confirmation Letter) bukan merupakan tanggung jawab tim Diorama Training.

LOKASI

REGULER TRAINING

Yogyakarta, Hotel Fortuna Grande Malioboro (6.000.000 IDR / participant)
Jakarta, Hotel Amaris Kemang La Codefin (6.500.000 IDR / participant)
Bandung, Hotel Neo Dipatiukur (6.500.000 IDR / participant)
Bali, Hotel Ibis Kuta (7.500.000 IDR / participant)
Lombok, Hotel Jayakarta (7.500.000 IDR / participant)
Surabaya, Hotel Neo Gubeng (7.500.000 IDR / participant)

ONLINE TRAINING VIA ZOOM

INVESTASI

Investasi pelatihan selama tiga hari tersebut menyesuaikan dengan jumlah peserta (on call). *Please feel free to contact us.

Catatan: Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.

Benefit Apa Saja yang Didapatkan Peserta?

FREE Airport pickup service (Gratis Antar jemput Hotel/Bandara)
FREE Transportasi Peserta ke tempat pelatihan (By Request)
Module / Handout
FREE Flashdisk
Sertifikat
FREE Bag or backpack (Tas Training)
Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
2x Coffee Break & 1 Lunch, Dinner
FREE Souvenir Exclusive

FAQ tentang Diotraining

P : Berapa minimal running pelatihan ini ?
J : Pelatihan ini akan running idealnya minimal dengan 3 peserta, tetapi bisa disesuaikan dengan kebutuhan peserta

P : Apakah bisa jika saya hanya ingin pelatihan sendiri aja / private course ?
J : Bisa, kami akan membantu menyelenggarakan pelatihan 1 hari jika ada persetujuan dari klien

P : Dimana saja pelatihan biasanya di selenggarakan?
J : Pelatihan kami selenggarakan di beberapa kota besar di Indonesia seperti Bandung, Jakarta, Yogyakarta, Surabaya, Malang, Bali, Lombok dan beberapa negara seperti Singapore dan Malaysia

P : Apakah bisa diselenggarakan selain di kota lain?
J : Penyelenggaraan pelatihan bisa diadakan di kota lain dengan minimal kuota 5 orang setiap kelas

P : Apakah bisa juga diselenggarakan secara IHT/ In House Training di Perusahaan klien ?
J : Bisa diselenggarakan secara IHT di Perusahaan klien

P : Apakah jadwal bisa disesuaikan dengan kebutuhan klien ?
J : Jadwal pelatihan dapat di sesuaikan dengan kebutuhan klien.

Materi, Lokasi dan Jadwal Pelatihan Bisa Berubah Sewaktu-waktu dan disesuaikan Dengan Kondisi Peserta, dimohon untuk Melakukan Konfirmasi untuk Segala Bentuk Perubahan, agar Tidak Terjadi Miskomunikasi. Segera Daftarkan Pelatihan, Dapatkan Promo Menarik Bulan Ini.

Beberapa Klien Kami

Silabus Training ini di edit oleh Wafa Setiawan sebagai Content Writer Spesialis. Tim Diorama Training di bidang Pelatihan Konsultasi Sumbedaya Manusia dan Sertifikasi.

Post Views: 326