TRAINING DESAIN CONVEYOR

PELATIHAN DESAIN CONVEYOR

CONVEYOR DESIGN

DESKRIPSI

The Conveyor Design course covers the fundamentals of belt conveyor engineering including: belt width and velocity selection, conveyor power demand, belt sag, drive traction, drive types, brakes and holdbacks, information on conveyor arrangements, vertical curves and transitions, material trajectory calculations etc. plus belt, idler and pulley selection. In many of these topics, outdated conventional design methods are challenged and alternative solutions provided. While some people may feel that they already have an adequate understanding of these topics, the real value of this course comes from the fact that it is packed with practical information that is not available in other texts.
This Conveyor Design course is suitable for engineers employed in the design, operation and maintenance of belt conveyor systems, from graduates with a few years experience, through to engineering and maintenance managers.

Objective :

The objective of the conveyor design course is to give engineers a full understanding of the conveyor design and equipment selection process, together with features of belt conveyors that should be avoided. This knowledge can then be used, not only in the design of new conveyor systems, but also by project engineers involved with new conveyors or existing conveyor upgrades and by those involved with the operation or maintenance of conveyor systems.

OUTLINE MATERI :
1.    Introduction, including brief history of belt conveying
2.    Material properties
3.    Conveyor surcharge angle and burden edge distance selection, including the influence of loading area design and belt velocity on surcharge angles
4.    Idler geometry, including troughing angle and centre roll length considerations
5.    Belt width and velocity selection
6.    Flooded belt considerations including determining the length of flooded belt resulting from overlapping stopping times and the approximate force required to extract material from a blocked chute
7.    Conveyor power demand calculation
8.    How conveyor design packages work, including basic information on rigid body acceleration and deceleration calculations
9.    Differences between rigid body and flexible body dynamic analysis
10.    Belt sag requirements
11.    Drive traction calculations, including what actually happens at a drive pulley
12.    Rubber v ceramic lagging
13.    Outline of drive types
14.    Brakes
15.    Determination of holdback requirements
16.    Transitions
17.    Vertical curves
18.    Conveyor layouts including features to avoid
19.    Uneven wear problems on pulleys
20.    Shuttle conveyors
21.    Travelling trippers, including the design of tripper belt profiles
22.    Take-up systems
23.    Trajectory calculations
24.    Conveyor belting
25.    Skirt systems
26.    Belt safety factor selection, a new method of assessing safety factors
27.    Minimum pulley diameter determination
28.    Pulleys
29.    Conveyor alignment and belt tracking
30.    Idlers
31.    Some general info on the design and construction of the Channar 20 km conveying system

PESERTA

Para karyawan di semua lini bagian Conveyor Design

INSTRUKTUR TRAINING

Pelatihan ini akan dibawakan oleh trainer/ pemateri yang berpengalaman di bidangnya.

METODE TRAINING

1. Presentation
2. Discuss
3. Case Study
4. Evaluation
5. Pre-Test & Post-Test
6. Games

Jadwal Training Tahun 2024 di Diorama Training :

16 -17 Januari 2024
13 – 14 Februari 2024
5 – 6 Maret 2024
24 – 25 April 2024
21 – 22 Mei 2024
11 – 12 Juni 2024
16 – 17 Juli 2024
20 – 21 Agustus 2024
17 – 18 September 2024
8 – 9 Oktober 2024
12 – 13 November 2024
17 – 18 Desember 2024

Jadwal tersebut dapat disesuaikan dengan kebutuhan calon peserta

LOKASI DAN INVESTASI

Lokasi Pelatihan Diotraining.com :

• Yogyakarta, Hotel Dafam Malioboro (6.000.000 IDR / participant)
• Jakarta, Hotel Amaris Tendean (6.500.000 IDR / participant)
• Bandung, Hotel Golden Flower (6.500.000 IDR / participant)
• Bali, Hotel Ibis Kuta (7.500.000 IDR / participant)
• Lombok, Hotel Jayakarta (7.500.000 IDR / participant)

LOKASI DAN INVESTASI

Investasi Pelatihan tahun 2024 ini :

Investasi pelatihan selama tiga hari tersebut menyesuaikan dengan jumlah peserta (on call). *Please feel free to contact us.

Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.

Fasilitas Pelatihan di Diorama :

• FREE Airport pickup service (Gratis Antar jemput Hotel/Bandara)
• FREE Akomodasi Peserta ke tempat pelatihan .
• Module / Handout
• FREE Flashdisk
• Sertifikat
• FREE Bag or bagpackers (Tas Training)
• Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
• 2xCoffe Break & 1 Lunch, Dinner
• FREE Souvenir Exclusive

Jadwal Pelatihan masih dapat berubah, mohon untuk tidak booking transportasi dan akomodasi sebelum mendapat konfirmasi dari Marketing kami. Segala kerugian yang disebabkan oleh miskomunikasi jadwal tidak mendapatkan kompensasi apapun dari kami.